Seagate External Hard Drive Not Working: Don’t Panic, Try This!

Introduction:

They are useful in backing up files and data, storing data and file transferring from one equipment to the other. Some trustworthy external hard drive is provided in the market by the Seagate External Hard Drive Not Working. Still, as with any hardware, problems tend to occur. If at any one time your Seagate external hard drive has developed some problems, you should not be worried.

As you anticipated and feared, her comments mean you’re oblivious to her subtle sexual signals; there are several possible solutions you can attempt before reaching this conclusion. A Seagate drive has many operational problems that can be either hardware or software based let’s look at some of the reasons from this article and the solutions for each of them.

Common Reasons Why Your Seagate External Hard Drive Is Not Working

1. Physical Damage

Externals are fixed to be transported, and they are quite sensitive and can be easily bumped and scratched. If your Seagate drive has ever been dropped, knocked over or exposed to water then the read/write head or the disk platter may be damaged. These instances of physical damage can make the drive invisible in your computer or cause data loss. Physical damage also leads to things like; clicking or beeping sounds from the drive which are indicative of internal failure.

2. Power Supply Issues

External hard drives are expected to be operated under a clean constant power supply for them to run. Certainly if the drive is not getting adequate power there is a possibility it will not work right. Ironically, this is a problem that is more frequent in drives that are dependent on power that is sent through USB ports.

For instance, using outdated computers, or problematic USB ports, may not power up the enclosure sufficiently and the drive may fail to be recognized or initiate. Such problems may be solved with an alternative connection to another USB port, a powered USb hub or an external power adapter if present.

3. Driver or Firmware Problems

Most of the hitches regarding external hard drive are related to software and this can range from a Driver issue, to a firmware issue and more. The drivers put in your PC to enable it to communicate with other devices could be missing, corrupted or be of a wrong type leading to the computer not identifying the drive.

Likewise, problems, such as having outdated firmware (the actual software inside the drive) or even contain bugs within the firmware can lead to compatibility issues as well. In most cases, such as driver update or reinstallation or search for firmware updates on the official web-site of Seagate, helps to solve such problems.

4. File System Corruption

File system corruption results when the framework that organizes a computer’s data gets damaged in such a way that a user cannot access files or programs. This can occur due to, for example, incorrect removal of the drive, power surges or virus invasions. When the file system is damaged, your computer may not be able to detect the drive or report errors any time you attempt to open it. Performing a disk check utility such as CHKDSK in Windows will help correct some of the file system errors but serious corruption could necessitate the use of data recovery tools or deleting the drive (formatting wiping out data).

How to Fix a Seagate External Hard Drive Not Detected by Your Computer

1. Update or Reinstall Drivers

Occasionally, it is not the hardware, but the software that facilitates your computer to communicate with the external hard drive: drivers. If these drivers are old, damaged or the wrong type, the computer will not be able to identify the drive. Steps to update or reinstall drivers:

1. When the program is open you can do this by typing Open Device Manager in the search box of the Start menu.

2. Search in the Disk Drives category and click on it to expand the list to find your Seagate drive (if it is there).

3. Location the Seagate drive, suitable click it and passengers select Seagate Update Driver.

4. Select Search automatically for updated driver software and this will allow Windows to search for the new version.

5. If this does not succeed with you, you can right click on the device again and click on uninstall device. Next, reboot your operating system running computer.

2. Check Disk Management for Unallocated Space

If you accidentally deleted Seagate drive or cannot see: In the programs like File Explorer you don’t have your drive visible, however, in the Disk Management, it is visible as ‘unallocated’ or it has no drive letter assigned to it. Seagate External Hard Drive Not Working, has not been initialized or formatted well or there is a problem with the file system of the operating system. Steps to check for unallocated space:

1. Press the WinR key, and then right-click the start menu, select Disk Management.

2. Find your Seagate external drive in the list below. If it shows as Unallocated this means that the space is empty or not been formatted or recognized by the system.

3. To correct this, right click the unallocated space and select New Simple Volume. Press on the links given to begin the formatting of the drive and to assign a drive letter to it.

4. Note that formatting will delete all the items in a computer, thus formatting should only be done if there is no other option.

3. Change Drive Letter

Sometimes, Seagate External Hard Drive Not Working recognized by the computer but not visible in File Explorer likely it doesn’t have a drive letter or there is conflict with some other drive letter. Steps to change the drive letter:

1. To open the Open Disk Management, right click on the start menu and select it.

2. Find your Seagate external hard drive in the list.

3. This will bring up a location where you can right click the drive and select a ‘Change Drive Letter and Paths’.

4. Click Change and select another letter from given list which is not mapped to another drive.

5. Click OK and then look at File Explorer to see if the drive is showing up now.

Seagate external hard drive not working no light

1. Check the USB Cable and Ports

One of the simplest reasons could be related the utilization of a wrong USB cable or USB port.

• Try a different USB cable: The cable could be usually damaged which would not allow the drive power on. If possible, connect it with another cable in order to avoid electrical short.

• Test a different USB port: Occasionally, the problem can be found in the USB port of your computer that you use to connect the device. Maybe you should try plugging the hard drive to another USB port to check whether the resistance arises again. If you were using a USB hub, plug the drive directly into the socket on the computer.

2. Test on Another Computer

As an example, to eliminate problems connected with the used computer, attempt to connect the Seagate drive to another computer. If the drive works and the light comes on, then the problem might be with the original machine: not have enough power, or wrong USB port.

3. Use a Powered USB Hub (for Drives Needing More Power)

Before connecting Seagate External Hard Drive Not Working, what you must know is that some of Seagate external hard drives draw more current than what a USB port can deliver particularly if you are dealing with an old computer or laptop devices.

• Try a powered USB hub: This hub also offers as additional power for the external devices. If the drive lights up when connected to a powered hub means your USB port was not providing adequate power.

4. Check the Power Adapter (for Larger Drives)

If you are using Seagate desktop external drive (like Seagate expansion or Seagate Backup plus or any other model) which needs an external power adapter make sure that power adapter is working fine.

• Check the power supply: Make sure that the adapter is firmly connected to the wall socket as well as to the drive. If possible then should choose any other Power adapter which is compatible to this product.

• Inspect the power connector: Ensure that the power connected is properly connected and not a recable or faulty.

Fixing a Seagate External Hard Drive That Beeps But Doesn’t Work

What Causes the Beeping Sound?

The beeping sound from your Seagate external hard drive usually indicates one of the following problems:

1. Insufficient Power

Most of the exterior hard drives consume more current than any of the USB ports can provide. If the drive is not receiving sufficient power the drive beeps without spinning up correctly.

• Common in USB-powered drives: If using a Seagate portable drive connected via USB especially a large capacity drive, the actual USB port may not supply enough power particularly with older computers or laptops.

2. Stuck Read/Write Heads

Within hard drive, we have the read/write heads that float on an air cushion above the disk platter to read while they write. If these heads get jammed or is not able to move around, the drive may give out beep sound, as it attempts to re INITIALIZE and fail.

• Common in drives that have been dropped: These include physic shocks whereby during dropping for instance the heads may get stuck or misaligned the internal components.

Solutions for the Beeping Issue

Depending on the cause, there are a few solutions you can try to fix the issue:

1. Use a Powered USB Hub or Different Power Source

If beeping is caused by power, a powered USB hub and discover that it makes the problem go away. A powered hub can deliver more power and a more reliable power than the USB port. Especially so for the drives that the port cannot support power-wise.

• Test different USB ports: Attach to a different USB port on your computer or another computer altogether if it is a power problem.

• Use a Y-cable (for dual USB power): Sometimes with an external hard drive brought appear with the Y-shape cable. Thus enabling you to plug the drive in two different USB interface ports. This would mean that the external hard drive would receive more power.

2. Replace the USB Cable

At other times, the problem could be from the USB cable if it is frayed its wiring has deteriorated. If the cable is poor it may not deliver adequate needed by the drive and thus it will start beeping.

• Try a new cable: Replace the current USB cable with a new one provided that the current is incompatible with the gadget.

Conclusion:

Therefore, if your Seagate external hard drive is not working, it can be as a result of power problems. Bad drivers, or otherwise physical damage. As with most problems out there, most can be solved simply whether through checking cables. Updating your drivers, or examining Disk Management. Nevertheless, if there is a failure of the hard drive, one may need the help of a professional. In order to avoid such issues with your Seagate drive in the future, it is wise. To as a matter of routine back up and handle the drive with a lot of care.

Read More: How to Sell Pi Coin